vibe-openscad

tier-2-offset-handle-mug / gemini-3.6-flash

2 run / 累計 7.8s / 累計 $0.0046

gemini flash 3.6 bare-think-off

bare (provider default effort)

run detail →
render
bare render of tier-2-offset-handle-mug
loading STL…
success 3.9s · 232/570t · $0.0023
SCAD (59 lines) 
// Mug Parameters
outer_d = 80;
inner_d = 70;
height = 90;
bottom_thickness = 6;

// Handle Parameters
handle_inner_h = 30;
handle_inner_w = 25;
handle_thickness = 8;
$fn = 100;

module mug_body() {
    difference() {
        // Outer Cylinder
        cylinder(d = outer_d, h = height);
        
        // Inner Hollow Part
        translate([0, 0, bottom_thickness])
            cylinder(d = inner_d, h = height - bottom_thickness + 1);
    }
}

module handle() {
    handle_outer_h = handle_inner_h + handle_thickness * 2;
    handle_outer_w = handle_inner_w + handle_thickness;
    
    // Position the handle at the center height and attached to the +X side
    translate([outer_d / 2, 0, height / 2]) {
        rotate([90, 0, 0]) {
            difference() {
                // Outer D-shape profile
                hull() {
                    cylinder(r = handle_outer_h / 2, h = handle_thickness, center = true);
                    translate([handle_outer_w - handle_outer_h / 2, 0, 0])
                        cylinder(r = handle_outer_h / 2, h = handle_thickness, center = true);
                }
                
                // Inner D-shape hole
                hull() {
                    translate([0, 0, 0])
                        cylinder(r = handle_inner_h / 2, h = handle_thickness + 2, center = true);
                    translate([handle_inner_w - handle_inner_h / 2, 0, 0])
                        cylinder(r = handle_inner_h / 2, h = handle_thickness + 2, center = true);
                }
                
                // Cut off the overlapping part inside the mug inner radius to keep clean interior
                translate([-handle_outer_h, -handle_outer_h, -(handle_thickness + 2)/2])
                    cube([handle_outer_h, handle_outer_h * 2, handle_thickness + 2]);
            }
        }
    }
}

// Final Union
union() {
    mug_body();
    handle();
}
パラメータ (7) —
スライダを動かすと openscad-wasm で再レンダリング

prompt

OpenSCAD で、向きが指定されたマグカップを作ってください。

本体:
- 外径 80mm、内径 70mm(肉厚 5mm)、高さ 90mm の円筒形マグ
- 底面の厚みは 6mm
- 内側は飲み物を入れられるよう中空

取手(handle):
- マグの **+X 軸方向の側面のみ** に付ける(他の方向には付けない)
- 取手は D 字形状(外側が半円、本体側が直線)で、本体外周にしっかり接続する
- 取手の内側の空間は高さ 30mm × 幅 25mm(指 3 本ぐらい入る)
- 取手はマグの高さ方向の中央付近に付ける
- 本体と取手は確実に union され、マニフォールド(隙間や宙吊りなし)を保つ

完成したコード全体を ```openscad ... ``` のフェンスで囲んで出力してください。コードのみで、追加の説明は不要です。

variant: thinking

offnot run
—
adaptivenot run
—
dynamic (default) success →
dynamic
3.9s · 232/570t · $0.0023
SCAD (59 lines) 
// Mug Parameters
outer_d = 80;
inner_d = 70;
height = 90;
bottom_thickness = 6;

// Handle Parameters
handle_inner_h = 30;
handle_inner_w = 25;
handle_thickness = 8;
$fn = 100;

module mug_body() {
    difference() {
        // Outer Cylinder
        cylinder(d = outer_d, h = height);
        
        // Inner Hollow Part
        translate([0, 0, bottom_thickness])
            cylinder(d = inner_d, h = height - bottom_thickness + 1);
    }
}

module handle() {
    handle_outer_h = handle_inner_h + handle_thickness * 2;
    handle_outer_w = handle_inner_w + handle_thickness;
    
    // Position the handle at the center height and attached to the +X side
    translate([outer_d / 2, 0, height / 2]) {
        rotate([90, 0, 0]) {
            difference() {
                // Outer D-shape profile
                hull() {
                    cylinder(r = handle_outer_h / 2, h = handle_thickness, center = true);
                    translate([handle_outer_w - handle_outer_h / 2, 0, 0])
                        cylinder(r = handle_outer_h / 2, h = handle_thickness, center = true);
                }
                
                // Inner D-shape hole
                hull() {
                    translate([0, 0, 0])
                        cylinder(r = handle_inner_h / 2, h = handle_thickness + 2, center = true);
                    translate([handle_inner_w - handle_inner_h / 2, 0, 0])
                        cylinder(r = handle_inner_h / 2, h = handle_thickness + 2, center = true);
                }
                
                // Cut off the overlapping part inside the mug inner radius to keep clean interior
                translate([-handle_outer_h, -handle_outer_h, -(handle_thickness + 2)/2])
                    cube([handle_outer_h, handle_outer_h * 2, handle_thickness + 2]);
            }
        }
    }
}

// Final Union
union() {
    mug_body();
    handle();
}