vibe-openscad

tier-3-butt-hinge / gemma-4-31b-it

2 run / 累計 372.1s / 累計 $0

gemini gemma 4 31b bare

bare (provider default effort)

run detail →
render
bare render of tier-3-butt-hinge
loading STL…
success 186.1s · 515/6699t · $0
SCAD (82 lines)
$fn = 64;

// --- Dimensions ---
leaf_w = 25;        // Width of the rectangular plate
leaf_h = 30;        // Height of the leaf (along axis)
leaf_t = 2;         // Thickness of the plate
knuckle_od = 8;     // Outer diameter of knuckle
knuckle_id = 4.6;   // Inner diameter (pin 4mm + 0.6mm clearance)
knuckle_seg = 6;    // Segment height (30mm / 5)

pin_d = 4;          // Pin diameter
pin_l = 32;         // Pin total length

screw_d = 3.2;      // M3 clearance hole
screw_cs_d = 6;     // Countersink diameter
screw_cs_h = 1;     // Countersink depth
screw_pitch = 8;    // Y-axis pitch between holes

// --- Modules ---

module leaf_part(side="left") {
    is_left = (side == "left");
    
    // Mirror the leaf for the left side
    mirror([is_left ? 1 : 0, 0, 0]) {
        difference() {
            union() {
                // Main Plate
                translate([0, 0, -leaf_t/2]) 
                    cube([leaf_w, leaf_h, leaf_t]);
                
                // Knuckles
                if (is_left) {
                    // Left leaf: Indices 0, 2, 4 (Outer and Center)
                    for (y = [0, knuckle_seg * 2, knuckle_seg * 4]) {
                        translate([0, y, 0]) 
                            cylinder(d=knuckle_od, h=knuckle_seg);
                    }
                } else {
                    // Right leaf: Indices 1, 3 (Intermediate)
                    for (y = [knuckle_seg, knuckle_seg * 3]) {
                        translate([0, y, 0]) 
                            cylinder(d=knuckle_od, h=knuckle_seg);
                    }
                }
            }
            
            // Pin Hole (Internal diameter for the axis)
            translate([0, -0.1, 0]) 
                cylinder(d=knuckle_id, h=leaf_h + 0.2);
            
            // Screw Holes (3 per leaf)
            // Center X on the flat part: (knuckle_radius + leaf_width) / 2
            hole_x = (knuckle_od/2 + leaf_w) / 2;
            for (y = [7, 15, 23]) { // Pitched 8mm, centered in 30mm
                // Through hole
                translate([hole_x, y, -leaf_t/2 - 0.1]) 
                    cylinder(d=screw_d, h=leaf_t + 0.2);
                // Countersink (taper)
                translate([hole_x, y, leaf_t/2 - screw_cs_h]) 
                    cylinder(d1=screw_d, d2=screw_cs_d, h=screw_cs_h);
            }
        }
    }
}

module pin_axis() {
    // Pin length 32mm, centered along 30mm knuckle (1mm overhang each end)
    translate([0, -1, 0]) 
        cylinder(d=pin_d, h=pin_l);
}

// --- Assembly ---

// Left Leaf (x < 0)
leaf_part("left");

// Right Leaf (x > 0)
leaf_part("right");

// Pin Axis (centered on Y axis)
pin_axis();
パラメータ (12) —
スライダを動かすと openscad-wasm で再レンダリング

prompt

OpenSCAD で、家具用の小型バット蝶番(butt hinge)を作ってください。
3 つのパーツ(左板、右板、ピン軸)が組み合わさって動作する完成品を、
「開いた状態(180°)」で 1 つの SCAD ファイルに配置して出力します。

寸法と配置:
- 板(leaf)2 枚: 30mm × 25mm × 厚さ 2mm の鉄板形状
  - 縦 30mm の辺がピン軸に沿う(ヒンジ軸方向)
  - 横 25mm の辺が回転で開く方向に伸びる
- ピン軸: 直径 4mm の円柱、長さ 32mm(両端 1mm ずつ knuckle から飛び出す)
- knuckle(筒部): 縦 30mm を 5 等分(各 6mm)に区切り、左板に 3 個・右板に 2 個を
  互い違いに配置(左板は外側 2 個 + 中央 1 個、右板は中間 2 個)
- knuckle 外径 8mm、内径はピン軸 + 0.3mm クリアランス(= 4.6mm 穴)
- 左板と右板はピン軸を共有して回転可能。180° 開いた状態で、両板の
  平らな面が同一平面に来るように配置する
- 各板の knuckle から離れた側に、M3 用の皿穴を 3 個ずつ
  (穴ピッチは板の縦方向に 8mm 間隔、皿穴は表面から見て直径 6mm × 深さ 1mm
  のテーパ + 直径 3.2mm の貫通穴)

座標系:
- ピン軸の中心線を Y 軸に重ねる(ピン軸は +Y 方向)
- 板の平らな面は Z 軸に直交し、左板が x<0 側、右板が x>0 側に伸びる(180° 開)
- knuckle は X=0 を中心とし、Y 方向に 6mm ずつ並ぶ

完成したコード全体を ```openscad ... ``` のフェンスで囲んで出力してください。
コードのみで、追加の説明は不要です。

variant: thinking

offnot run
—
adaptivenot run
—
dynamic (default) success →
dynamic
186.1s · 515/6699t · $0
SCAD (82 lines)
$fn = 64;

// --- Dimensions ---
leaf_w = 25;        // Width of the rectangular plate
leaf_h = 30;        // Height of the leaf (along axis)
leaf_t = 2;         // Thickness of the plate
knuckle_od = 8;     // Outer diameter of knuckle
knuckle_id = 4.6;   // Inner diameter (pin 4mm + 0.6mm clearance)
knuckle_seg = 6;    // Segment height (30mm / 5)

pin_d = 4;          // Pin diameter
pin_l = 32;         // Pin total length

screw_d = 3.2;      // M3 clearance hole
screw_cs_d = 6;     // Countersink diameter
screw_cs_h = 1;     // Countersink depth
screw_pitch = 8;    // Y-axis pitch between holes

// --- Modules ---

module leaf_part(side="left") {
    is_left = (side == "left");
    
    // Mirror the leaf for the left side
    mirror([is_left ? 1 : 0, 0, 0]) {
        difference() {
            union() {
                // Main Plate
                translate([0, 0, -leaf_t/2]) 
                    cube([leaf_w, leaf_h, leaf_t]);
                
                // Knuckles
                if (is_left) {
                    // Left leaf: Indices 0, 2, 4 (Outer and Center)
                    for (y = [0, knuckle_seg * 2, knuckle_seg * 4]) {
                        translate([0, y, 0]) 
                            cylinder(d=knuckle_od, h=knuckle_seg);
                    }
                } else {
                    // Right leaf: Indices 1, 3 (Intermediate)
                    for (y = [knuckle_seg, knuckle_seg * 3]) {
                        translate([0, y, 0]) 
                            cylinder(d=knuckle_od, h=knuckle_seg);
                    }
                }
            }
            
            // Pin Hole (Internal diameter for the axis)
            translate([0, -0.1, 0]) 
                cylinder(d=knuckle_id, h=leaf_h + 0.2);
            
            // Screw Holes (3 per leaf)
            // Center X on the flat part: (knuckle_radius + leaf_width) / 2
            hole_x = (knuckle_od/2 + leaf_w) / 2;
            for (y = [7, 15, 23]) { // Pitched 8mm, centered in 30mm
                // Through hole
                translate([hole_x, y, -leaf_t/2 - 0.1]) 
                    cylinder(d=screw_d, h=leaf_t + 0.2);
                // Countersink (taper)
                translate([hole_x, y, leaf_t/2 - screw_cs_h]) 
                    cylinder(d1=screw_d, d2=screw_cs_d, h=screw_cs_h);
            }
        }
    }
}

module pin_axis() {
    // Pin length 32mm, centered along 30mm knuckle (1mm overhang each end)
    translate([0, -1, 0]) 
        cylinder(d=pin_d, h=pin_l);
}

// --- Assembly ---

// Left Leaf (x < 0)
leaf_part("left");

// Right Leaf (x > 0)
leaf_part("right");

// Pin Axis (centered on Y axis)
pin_axis();