bare/gemma-4-31b-it / tier-3-butt-hinge
success tier 3
bare (gemma 4 31b)
render
$fn = 64;
// --- Dimensions ---
leaf_w = 25; // Width of the rectangular plate
leaf_h = 30; // Height of the leaf (along axis)
leaf_t = 2; // Thickness of the plate
knuckle_od = 8; // Outer diameter of knuckle
knuckle_id = 4.6; // Inner diameter (pin 4mm + 0.6mm clearance)
knuckle_seg = 6; // Segment height (30mm / 5)
pin_d = 4; // Pin diameter
pin_l = 32; // Pin total length
screw_d = 3.2; // M3 clearance hole
screw_cs_d = 6; // Countersink diameter
screw_cs_h = 1; // Countersink depth
screw_pitch = 8; // Y-axis pitch between holes
// --- Modules ---
module leaf_part(side="left") {
is_left = (side == "left");
// Mirror the leaf for the left side
mirror([is_left ? 1 : 0, 0, 0]) {
difference() {
union() {
// Main Plate
translate([0, 0, -leaf_t/2])
cube([leaf_w, leaf_h, leaf_t]);
// Knuckles
if (is_left) {
// Left leaf: Indices 0, 2, 4 (Outer and Center)
for (y = [0, knuckle_seg * 2, knuckle_seg * 4]) {
translate([0, y, 0])
cylinder(d=knuckle_od, h=knuckle_seg);
}
} else {
// Right leaf: Indices 1, 3 (Intermediate)
for (y = [knuckle_seg, knuckle_seg * 3]) {
translate([0, y, 0])
cylinder(d=knuckle_od, h=knuckle_seg);
}
}
}
// Pin Hole (Internal diameter for the axis)
translate([0, -0.1, 0])
cylinder(d=knuckle_id, h=leaf_h + 0.2);
// Screw Holes (3 per leaf)
// Center X on the flat part: (knuckle_radius + leaf_width) / 2
hole_x = (knuckle_od/2 + leaf_w) / 2;
for (y = [7, 15, 23]) { // Pitched 8mm, centered in 30mm
// Through hole
translate([hole_x, y, -leaf_t/2 - 0.1])
cylinder(d=screw_d, h=leaf_t + 0.2);
// Countersink (taper)
translate([hole_x, y, leaf_t/2 - screw_cs_h])
cylinder(d1=screw_d, d2=screw_cs_d, h=screw_cs_h);
}
}
}
}
module pin_axis() {
// Pin length 32mm, centered along 30mm knuckle (1mm overhang each end)
translate([0, -1, 0])
cylinder(d=pin_d, h=pin_l);
}
// --- Assembly ---
// Left Leaf (x < 0)
leaf_part("left");
// Right Leaf (x > 0)
leaf_part("right");
// Pin Axis (centered on Y axis)
pin_axis(); パラメータ (12) —
スライダを動かすと openscad-wasm で再レンダリング
prompt
OpenSCAD で、家具用の小型バット蝶番(butt hinge)を作ってください。 3 つのパーツ(左板、右板、ピン軸)が組み合わさって動作する完成品を、 「開いた状態(180°)」で 1 つの SCAD ファイルに配置して出力します。 寸法と配置: - 板(leaf)2 枚: 30mm × 25mm × 厚さ 2mm の鉄板形状 - 縦 30mm の辺がピン軸に沿う(ヒンジ軸方向) - 横 25mm の辺が回転で開く方向に伸びる - ピン軸: 直径 4mm の円柱、長さ 32mm(両端 1mm ずつ knuckle から飛び出す) - knuckle(筒部): 縦 30mm を 5 等分(各 6mm)に区切り、左板に 3 個・右板に 2 個を 互い違いに配置(左板は外側 2 個 + 中央 1 個、右板は中間 2 個) - knuckle 外径 8mm、内径はピン軸 + 0.3mm クリアランス(= 4.6mm 穴) - 左板と右板はピン軸を共有して回転可能。180° 開いた状態で、両板の 平らな面が同一平面に来るように配置する - 各板の knuckle から離れた側に、M3 用の皿穴を 3 個ずつ (穴ピッチは板の縦方向に 8mm 間隔、皿穴は表面から見て直径 6mm × 深さ 1mm のテーパ + 直径 3.2mm の貫通穴) 座標系: - ピン軸の中心線を Y 軸に重ねる(ピン軸は +Y 方向) - 板の平らな面は Z 軸に直交し、左板が x<0 側、右板が x>0 側に伸びる(180° 開) - knuckle は X=0 を中心とし、Y 方向に 6mm ずつ並ぶ 完成したコード全体を ```openscad ... ``` のフェンスで囲んで出力してください。 コードのみで、追加の説明は不要です。