vibe-openscad

bare/gpt-6-sol / tier-2-offset-handle-mug

success tier 2

bare (gpt 6 sol)

render
bare render of tier-2-offset-handle-mug
loading STL…
success 19.8s · 273/1314t · $0.0137
SCAD (44 lines)
$fn = 96;

// Dimensions in mm
outer_radius = 40;
inner_radius = 35;
mug_height = 90;
bottom_thickness = 6;
handle_thickness = 14;
arc_steps = 48;

// A D-shaped outline in the X–Z plane:
// straight edge on the left, semicircular edge on the right.
module d_outline(left_x, arc_center_x, center_z, radius) {
    polygon(points = concat(
        [[left_x, center_z - radius]],
        [for (i = [0 : arc_steps])
            [arc_center_x + radius * cos(-90 + 180 * i / arc_steps),
             center_z + radius * sin(-90 + 180 * i / arc_steps)]],
        [[left_x, center_z + radius]]
    ));
}

module handle() {
    rotate([90, 0, 0])
        linear_extrude(height = handle_thickness, center = true)
            difference() {
                // The straight edge overlaps the mug wall for a solid join.
                d_outline(38, 52, 45, 25);
                // Opening: 30 mm high and 25 mm wide.
                d_outline(43, 53, 45, 15);
            }
}

union() {
    difference() {
        cylinder(h = mug_height, r = outer_radius);
        translate([0, 0, bottom_thickness])
            cylinder(h = mug_height - bottom_thickness + 1,
                     r = inner_radius);
    }

    // Handle only on the +X side.
    handle();
}
パラメータ (6) —
スライダを動かすと openscad-wasm で再レンダリング

meta

runIdbare_gpt-6-sol-358f1bcb108e-2026-10-06T19-30-09-220Z
matrixIdbare/gpt-6-sol
signature358f1bcb108e441b…
provideropenai
modelgpt-6-sol
harnessbare
statussuccess
duration19.78s (wallclock: load + prompt eval + generation + network)
tokens273 in / 1314 out
wallclock tok/s66.4 tok/s (end-to-end)
cost$0.0137
createdAt2026-10-06T19:30:09.220Z
gitCommitf205f3241c4c
openscadOpenSCAD version 2026.09.23

prompt

OpenSCAD で、向きが指定されたマグカップを作ってください。

本体:
- 外径 80mm、内径 70mm(肉厚 5mm)、高さ 90mm の円筒形マグ
- 底面の厚みは 6mm
- 内側は飲み物を入れられるよう中空

取手(handle):
- マグの **+X 軸方向の側面のみ** に付ける(他の方向には付けない)
- 取手は D 字形状(外側が半円、本体側が直線)で、本体外周にしっかり接続する
- 取手の内側の空間は高さ 30mm × 幅 25mm(指 3 本ぐらい入る)
- 取手はマグの高さ方向の中央付近に付ける
- 本体と取手は確実に union され、マニフォールド(隙間や宙吊りなし)を保つ

完成したコード全体を ```openscad ... ``` のフェンスで囲んで出力してください。コードのみで、追加の説明は不要です。