vibe-openscad

bare/gemma-4-31b-it / tier-2-offset-handle-mug

success tier 2

bare (gemma 4 31b)

render
bare render of tier-2-offset-handle-mug
loading STL…
success 97.1s · 232/3446t · $0
SCAD (44 lines)
$fn = 100;

// Parameters
outer_dia = 80;
inner_dia = 70;
height = 90;
bottom_thickness = 6;
wall_thickness = (outer_dia - inner_dia) / 2;

handle_void_h = 30;
handle_void_w = 25;
handle_thickness = 10; // thickness of the handle "wire"

union() {
    // --- Mug Body ---
    difference() {
        // Outer shell
        cylinder(h = height, d = outer_dia);
        
        // Inner hollow
        translate([0, 0, bottom_thickness])
            cylinder(h = height - bottom_thickness + 1, d = inner_dia);
    }

    // --- Handle ---
    // Positioned at +X axis, centered vertically
    translate([outer_dia / 2, 0, height / 2])
    rotate([0, 90, 0]) 
    // Scale the X-axis (which is the handle's width extension) 
    // to achieve the specific void width while keeping height circular
    scale([handle_void_w / (handle_void_h / 2), 1, 1])
    difference() {
        // Outer shape of the handle ring
        cylinder(h = handle_thickness, r = (handle_void_h / 2) + (handle_thickness / 2), center = true);
        
        // Inner void of the handle ring
        cylinder(h = handle_thickness + 2, r = handle_void_h / 2, center = true);
        
        // Cut off the half that would be inside the mug to create the D-shape
        // Offset the cube to ensure a clean cut and slight overlap for manifold union
        translate([-(handle_void_h / 2), 0, 0])
            cube([handle_void_h, handle_void_h * 2, handle_thickness + 2], center = true);
    }
}
パラメータ (7) —
スライダを動かすと openscad-wasm で再レンダリング

meta

runIdbare_gemma-4-31b-it-5f539603b191-2026-10-06T19-38-47-281Z
matrixIdbare/gemma-4-31b-it
signature5f539603b191443c…
providergoogle
modelgemma-4-31b-it
harnessbare
statussuccess
duration97.07s (wallclock: load + prompt eval + generation + network)
tokens232 in / 3446 out
wallclock tok/s35.5 tok/s (end-to-end)
cost$0
createdAt2026-10-06T19:38:47.281Z
gitCommitf9f85ea20c03
openscadOpenSCAD version 2026.09.23

prompt

OpenSCAD で、向きが指定されたマグカップを作ってください。

本体:
- 外径 80mm、内径 70mm(肉厚 5mm)、高さ 90mm の円筒形マグ
- 底面の厚みは 6mm
- 内側は飲み物を入れられるよう中空

取手(handle):
- マグの **+X 軸方向の側面のみ** に付ける(他の方向には付けない)
- 取手は D 字形状(外側が半円、本体側が直線)で、本体外周にしっかり接続する
- 取手の内側の空間は高さ 30mm × 幅 25mm(指 3 本ぐらい入る)
- 取手はマグの高さ方向の中央付近に付ける
- 本体と取手は確実に union され、マニフォールド(隙間や宙吊りなし)を保つ

完成したコード全体を ```openscad ... ``` のフェンスで囲んで出力してください。コードのみで、追加の説明は不要です。