vibe-openscad

bare-xhigh/gpt-6-luna / tier-2-l-bracket

success tier 2

bare (gpt 6 luna)

render
bare render of tier-2-l-bracket
loading STL…
success 39.6s · 294/4134t · $0.0021
SCAD (50 lines)
width = 50;
depth = 40;
height = 40;
thickness = 3;

hole_d = 4.5;
countersink_d = 8;
countersink_depth = 2;
edge_inset = 10;
eps = 0.01;

hole_x = [-width / 2 + edge_inset, width / 2 - edge_inset];

difference() {
    union() {
        // 水平フランジ
        translate([-width / 2, 0, -thickness])
            cube([width, depth, thickness]);

        // 垂直フランジ
        translate([-width / 2, -thickness, 0])
            cube([width, thickness, height]);

        // コーナーの接続部
        translate([-width / 2, -thickness, -thickness])
            cube([width, thickness, thickness]);
    }

    for (x = hole_x) {
        // 水平フランジの皿穴(外側は -Z 側)
        for (y = [edge_inset, depth - edge_inset]) {
            translate([x, y, -thickness - eps])
                cylinder(h = thickness + 2 * eps, d = hole_d);

            translate([x, y, -thickness])
                cylinder(h = countersink_depth, d1 = countersink_d, d2 = hole_d);
        }

        // 垂直フランジの皿穴(外側は -Y 側)
        for (z = [edge_inset, height - edge_inset]) {
            translate([x, -thickness - eps, z])
                rotate([-90, 0, 0])
                    cylinder(h = thickness + 2 * eps, d = hole_d);

            translate([x, -thickness, z])
                rotate([-90, 0, 0])
                    cylinder(h = countersink_depth, d1 = countersink_d, d2 = hole_d);
        }
    }
}
パラメータ (9) —
スライダを動かすと openscad-wasm で再レンダリング

meta

runIdbare-xhigh_gpt-6-luna-b283e0bcfedf-2026-10-06T19-31-34-172Z
matrixIdbare-xhigh/gpt-6-luna
signatureb283e0bcfedffa59…
provideropenai
modelgpt-6-luna
harnessbare
statussuccess
duration39.57s (wallclock: load + prompt eval + generation + network)
tokens294 in / 4134 out
wallclock tok/s104.5 tok/s (end-to-end)
cost$0.0021
createdAt2026-10-06T19:31:34.172Z
gitCommitf205f3241c4c
openscadOpenSCAD version 2026.09.23

prompt

OpenSCAD で、L 字に折れた金具(L-bracket)を作ってください。

形状:
- 水平面と垂直面の 2 つのフランジが直角に繋がっている
- 水平面は 50mm × 40mm(幅 × 奥行き)
- 垂直面は 50mm × 40mm(幅 × 高さ)
- 板厚はどちらも 3mm
- 内側コーナーが原点になるように配置(水平面は +Y 方向、垂直面は +Z 方向に伸びる)

皿穴(countersunk holes):
- 各面に 2 個ずつ、合計 4 個
- M4 ねじ用(貫通穴 Φ4.5mm + 皿座面 Φ8mm × 深さ 2mm)
- 各面の中心線上で、面の縁から 10mm 内側、左右対称に 2 個並べる
- 皿座面は外側(ボルト頭が当たる側)に向ける

完成したコード全体を ```openscad ... ``` のフェンスで囲んで出力してください。コードのみで、追加の説明は不要です。