vibe-openscad

bare-low/gpt-6.1-sol / tier-2-offset-handle-mug

success tier 2

bare (gpt 6.1 sol)

render
bare render of tier-2-offset-handle-mug
loading STL…
success 22.4s · 273/810t · $0.0086
SCAD (74 lines)
$fn = 160;

outer_diameter = 80;
inner_diameter = 70;
mug_height = 90;
bottom_thickness = 6;

handle_opening_width = 25;
handle_opening_height = 30;
handle_wall = 8;
handle_depth = 10;

handle_center_z = mug_height / 2;
handle_body_edge_x = outer_diameter / 2 - 2;
handle_opening_edge_x = handle_body_edge_x + handle_wall;

// +X 側へ張り出す半楕円。直線側は x = 0。
module half_ellipse(rx, rz) {
    intersection() {
        scale([rx, rz])
            circle(r = 1);

        translate([0, -rz - 1])
            square([rx + 1, 2 * rz + 2]);
    }
}

module handle_profile() {
    difference() {
        union() {
            translate([handle_opening_edge_x, 0])
                half_ellipse(
                    handle_opening_width + handle_wall,
                    handle_opening_height / 2 + handle_wall
                );

            translate([
                handle_body_edge_x,
                -handle_opening_height / 2 - handle_wall
            ])
                square([
                    handle_wall,
                    handle_opening_height + 2 * handle_wall
                ]);
        }

        translate([handle_opening_edge_x, 0])
            half_ellipse(
                handle_opening_width,
                handle_opening_height / 2
            );
    }
}

module handle() {
    translate([0, 0, handle_center_z])
        rotate([90, 0, 0])
            linear_extrude(height = handle_depth, center = true)
                handle_profile();
}

render()
difference() {
    union() {
        cylinder(d = outer_diameter, h = mug_height);
        handle();
    }

    translate([0, 0, bottom_thickness])
        cylinder(
            d = inner_diameter,
            h = mug_height - bottom_thickness + 1
        );
}
パラメータ (8) —
スライダを動かすと openscad-wasm で再レンダリング

meta

runIdbare-low_gpt-6.1-sol-b185ff9cbbac-2026-10-06T19-30-45-877Z
matrixIdbare-low/gpt-6.1-sol
signatureb185ff9cbbacbbde…
provideropenai
modelgpt-6.1-sol
harnessbare
statussuccess
duration22.41s (wallclock: load + prompt eval + generation + network)
tokens273 in / 810 out
wallclock tok/s36.1 tok/s (end-to-end)
cost$0.0086
createdAt2026-10-06T19:30:45.877Z
gitCommit8cb022fa99b9
openscadOpenSCAD version 2026.09.23

prompt

OpenSCAD で、向きが指定されたマグカップを作ってください。

本体:
- 外径 80mm、内径 70mm(肉厚 5mm)、高さ 90mm の円筒形マグ
- 底面の厚みは 6mm
- 内側は飲み物を入れられるよう中空

取手(handle):
- マグの **+X 軸方向の側面のみ** に付ける(他の方向には付けない)
- 取手は D 字形状(外側が半円、本体側が直線)で、本体外周にしっかり接続する
- 取手の内側の空間は高さ 30mm × 幅 25mm(指 3 本ぐらい入る)
- 取手はマグの高さ方向の中央付近に付ける
- 本体と取手は確実に union され、マニフォールド(隙間や宙吊りなし)を保つ

完成したコード全体を ```openscad ... ``` のフェンスで囲んで出力してください。コードのみで、追加の説明は不要です。