vibe-openscad

bare-low/gpt-6-sol / tier-2-offset-handle-mug

success tier 2

bare (gpt 6 sol)

render
bare render of tier-2-offset-handle-mug
loading STL…
success 13.0s · 273/840t · $0.0089
SCAD (58 lines)
$fn = 128;

outer_d = 80;
inner_d = 70;
mug_h = 90;
bottom_thickness = 6;

handle_thickness = 12;
handle_center_z = mug_h / 2;
handle_outer_radius = 32;
handle_opening_width = 25;
handle_opening_height = 30;
handle_join_x = 37;             // 本体外周に食い込ませて接続
handle_straight_x = outer_d / 2;

module mug_body() {
    difference() {
        cylinder(h = mug_h, d = outer_d);
        translate([0, 0, bottom_thickness])
            cylinder(h = mug_h - bottom_thickness + 1, d = inner_d);
    }
}

module handle_profile() {
    difference() {
        union() {
            // 本体側の直線部分
            translate([handle_join_x, handle_center_z - handle_outer_radius])
                square([
                    handle_straight_x - handle_join_x,
                    2 * handle_outer_radius
                ]);

            // +X 側だけに広がる半円
            intersection() {
                translate([handle_straight_x, handle_center_z])
                    circle(r = handle_outer_radius);
                translate([handle_straight_x,
                           handle_center_z - handle_outer_radius])
                    square([handle_outer_radius, 2 * handle_outer_radius]);
            }
        }

        // 高さ 30 mm × 幅 25 mm の指を入れる空間
        translate([handle_straight_x,
                   handle_center_z - handle_opening_height / 2])
            square([handle_opening_width, handle_opening_height]);
    }
}

union() {
    mug_body();

    translate([0, handle_thickness / 2, 0])
        rotate([90, 0, 0])
            linear_extrude(height = handle_thickness)
                handle_profile();
}
パラメータ (9) —
スライダを動かすと openscad-wasm で再レンダリング

meta

runIdbare-low_gpt-6-sol-7455287ffeff-2026-10-06T19-30-22-281Z
matrixIdbare-low/gpt-6-sol
signature7455287ffeffb602…
provideropenai
modelgpt-6-sol
harnessbare
statussuccess
duration13.04s (wallclock: load + prompt eval + generation + network)
tokens273 in / 840 out
wallclock tok/s64.4 tok/s (end-to-end)
cost$0.0089
createdAt2026-10-06T19:30:22.281Z
gitCommitf205f3241c4c
openscadOpenSCAD version 2026.09.23

prompt

OpenSCAD で、向きが指定されたマグカップを作ってください。

本体:
- 外径 80mm、内径 70mm(肉厚 5mm)、高さ 90mm の円筒形マグ
- 底面の厚みは 6mm
- 内側は飲み物を入れられるよう中空

取手(handle):
- マグの **+X 軸方向の側面のみ** に付ける(他の方向には付けない)
- 取手は D 字形状(外側が半円、本体側が直線)で、本体外周にしっかり接続する
- 取手の内側の空間は高さ 30mm × 幅 25mm(指 3 本ぐらい入る)
- 取手はマグの高さ方向の中央付近に付ける
- 本体と取手は確実に union され、マニフォールド(隙間や宙吊りなし)を保つ

完成したコード全体を ```openscad ... ``` のフェンスで囲んで出力してください。コードのみで、追加の説明は不要です。