vibe-openscad

bare-high/gpt-6.1-sol / tier-2-offset-handle-mug

success tier 2

bare (gpt 6.1 sol)

render
bare render of tier-2-offset-handle-mug
loading STL…
success 51.0s · 273/2092t · $0.0215
SCAD (86 lines)
$fn = 180;

outer_diameter = 80;
inner_diameter = 70;
mug_height = 90;
bottom_thickness = 6;

handle_inner_width = 25;
handle_inner_height = 30;
handle_depth = 10;
handle_outer_thickness = 6;
handle_overlap = 3;

eps = 0.05;

body_radius = outer_diameter / 2;
handle_center_z = mug_height / 2;
handle_root_x = body_radius - handle_overlap;

// 外側を半円にし、開口部の幅25mm・高さ30mmを確保する。
handle_outer_radius =
    handle_inner_width + handle_outer_thickness + handle_overlap;

module mug_body() {
    difference() {
        cylinder(d = outer_diameter, h = mug_height);

        translate([0, 0, bottom_thickness])
            cylinder(
                d = inner_diameter,
                h = mug_height - bottom_thickness + eps
            );
    }
}

module handle_profile() {
    difference() {
        // 本体側が直線、+X側が半円の外形。
        intersection() {
            translate([handle_root_x, handle_center_z])
                circle(r = handle_outer_radius);

            translate([
                handle_root_x,
                handle_center_z - handle_outer_radius - eps
            ])
                square([
                    handle_outer_radius + eps,
                    2 * handle_outer_radius + 2 * eps
                ]);
        }

        // 内側のD字開口:幅25mm、高さ30mm。
        intersection() {
            translate([body_radius, handle_center_z])
                scale([
                    handle_inner_width,
                    handle_inner_height / 2
                ])
                    circle(r = 1);

            translate([
                body_radius,
                handle_center_z - handle_inner_height / 2 - eps
            ])
                square([
                    handle_inner_width + eps,
                    handle_inner_height + 2 * eps
                ]);
        }
    }
}

module mug_handle() {
    // 2DのXY平面をXZ平面へ回し、Y方向に厚みを付ける。
    // 直線側を本体外周に3mm埋め込み、確実に接続する。
    rotate([90, 0, 0])
        linear_extrude(height = handle_depth, center = true, convexity = 10)
            handle_profile();
}

render(convexity = 10)
    union() {
        mug_body();
        mug_handle();
    }
パラメータ (10) —
スライダを動かすと openscad-wasm で再レンダリング

meta

runIdbare-high_gpt-6.1-sol-750273a4aa82-2026-10-06T19-31-36-872Z
matrixIdbare-high/gpt-6.1-sol
signature750273a4aa8294e5…
provideropenai
modelgpt-6.1-sol
harnessbare
statussuccess
duration50.97s (wallclock: load + prompt eval + generation + network)
tokens273 in / 2092 out
wallclock tok/s41.0 tok/s (end-to-end)
cost$0.0215
createdAt2026-10-06T19:31:36.872Z
gitCommit8cb022fa99b9
openscadOpenSCAD version 2026.09.23

prompt

OpenSCAD で、向きが指定されたマグカップを作ってください。

本体:
- 外径 80mm、内径 70mm(肉厚 5mm)、高さ 90mm の円筒形マグ
- 底面の厚みは 6mm
- 内側は飲み物を入れられるよう中空

取手(handle):
- マグの **+X 軸方向の側面のみ** に付ける(他の方向には付けない)
- 取手は D 字形状(外側が半円、本体側が直線)で、本体外周にしっかり接続する
- 取手の内側の空間は高さ 30mm × 幅 25mm(指 3 本ぐらい入る)
- 取手はマグの高さ方向の中央付近に付ける
- 本体と取手は確実に union され、マニフォールド(隙間や宙吊りなし)を保つ

完成したコード全体を ```openscad ... ``` のフェンスで囲んで出力してください。コードのみで、追加の説明は不要です。