vibe-openscad

bare-high/gpt-6-luna / tier-2-l-bracket

success tier 2

bare (gpt 6 luna)

render
bare render of tier-2-l-bracket
loading STL…
success 19.3s · 294/1995t · $0.0010
SCAD (53 lines)
$fn = 64;

width = 50;
depth = 40;
height = 40;
thickness = 3;

through_diameter = 4.5;
countersink_diameter = 8;
countersink_depth = 2;
edge_offset = 10;

hole_x = [-width / 2 + edge_offset, width / 2 - edge_offset];

difference() {
    union() {
        // Horizontal flange: extends in +Y, with its inner face at Z=0
        translate([-width / 2, 0, -thickness])
            cube([width, depth, thickness]);

        // Vertical flange: extends in +Z, with its inner face at Y=0
        translate([-width / 2, -thickness, 0])
            cube([width, thickness, height]);

        // Material joining the flanges at the inner corner
        translate([-width / 2, -thickness, -thickness])
            cube([width, thickness, thickness]);
    }

    // Horizontal flange holes; countersinks face outward (-Z)
    for (x = hole_x) {
        translate([x, depth / 2, -thickness - 0.1])
            cylinder(h = thickness + 0.2, d = through_diameter);

        translate([x, depth / 2, -thickness])
            cylinder(h = countersink_depth,
                     d1 = countersink_diameter,
                     d2 = through_diameter);
    }

    // Vertical flange holes; countersinks face outward (-Y)
    for (x = hole_x) {
        translate([x, -thickness - 0.1, height / 2])
            rotate([-90, 0, 0])
                cylinder(h = thickness + 0.2, d = through_diameter);

        translate([x, -thickness, height / 2])
            rotate([-90, 0, 0])
                cylinder(h = countersink_depth,
                         d1 = countersink_diameter,
                         d2 = through_diameter);
    }
}
パラメータ (8) —
スライダを動かすと openscad-wasm で再レンダリング

meta

runIdbare-high_gpt-6-luna-8a1f7abbec09-2026-10-06T19-30-47-217Z
matrixIdbare-high/gpt-6-luna
signature8a1f7abbec0946ec…
provideropenai
modelgpt-6-luna
harnessbare
statussuccess
duration19.30s (wallclock: load + prompt eval + generation + network)
tokens294 in / 1995 out
wallclock tok/s103.4 tok/s (end-to-end)
cost$0.0010
createdAt2026-10-06T19:30:47.217Z
gitCommitf205f3241c4c
openscadOpenSCAD version 2026.09.23

prompt

OpenSCAD で、L 字に折れた金具(L-bracket)を作ってください。

形状:
- 水平面と垂直面の 2 つのフランジが直角に繋がっている
- 水平面は 50mm × 40mm(幅 × 奥行き)
- 垂直面は 50mm × 40mm(幅 × 高さ)
- 板厚はどちらも 3mm
- 内側コーナーが原点になるように配置(水平面は +Y 方向、垂直面は +Z 方向に伸びる)

皿穴(countersunk holes):
- 各面に 2 個ずつ、合計 4 個
- M4 ねじ用(貫通穴 Φ4.5mm + 皿座面 Φ8mm × 深さ 2mm)
- 各面の中心線上で、面の縁から 10mm 内側、左右対称に 2 個並べる
- 皿座面は外側(ボルト頭が当たる側)に向ける

完成したコード全体を ```openscad ... ``` のフェンスで囲んで出力してください。コードのみで、追加の説明は不要です。