vibe-openscad

tier-2-hex-bolt / o4-mini-2025-04-16

7 run / 累計 86.4s / 累計 $0.0483

openai o4 mini 2025-04-16 bare

bare (provider default effort)

run detail →
render
bare render of tier-2-hex-bolt
loading STL…
success 16.5s · 200/1854t · $0.0084
SCAD (3 lines) 
cylinder(h = 5.3, r = 13/(2*cos(PI/6)), $fn = 6);
translate([0, 0, -30])
    cylinder(h = 30, r = 4, $fn = 64);

prompt

OpenSCAD で、規格に準じた M8 サイズの六角ボルトを作ってください。
ねじ山自体は省略してよく、円柱のシャンクで構いません。

寸法は以下に従ってください:
- 頭部は六角柱で、対辺距離(across-flats)13mm、高さ 5.3mm
- シャンク(軸部)は直径 8mm、長さ 30mm の円柱
- ボルト全体の中心軸は +Z 軸方向
- 頭部の底面が原点(z=0)に来るように配置し、シャンクは z<0 側へ伸ばす

完成したコード全体を ```openscad ... ``` のフェンスで囲んで出力してください。コードのみで、追加の説明は不要です。

variant: effort

low success →
low
10.5s · 200/1457t · $0.0066
SCAD (10 lines) 
d_hex = 26/sqrt(3);
h_head = 5.3;
d_shaft = 8;
l_shaft = 30;

union() {
    cylinder(d = d_hex, h = h_head, $fn = 6);
    translate([0, 0, -l_shaft])
        cylinder(d = d_shaft, h = l_shaft);
}
medium (default) success →
medium
16.5s · 200/1854t · $0.0084
SCAD (3 lines) 
cylinder(h = 5.3, r = 13/(2*cos(PI/6)), $fn = 6);
translate([0, 0, -30])
    cylinder(h = 30, r = 4, $fn = 64);
high success →
high
14.6s · 200/1725t · $0.0078
SCAD (7 lines) 
module bolt() {
    cylinder(h=5.3, r=(13/2)/cos(30), $fn=6);
    translate([0,0,-30])
        cylinder(h=30, r=4, $fn=64);
}

bolt();
maxnot run
—
xhighnot run
—

iteration: iter-png

i1 success →
iter 1
11.8s · 1176/1136t · $0.0063
diff vs bare: +0/-0 
  cylinder(h = 5.3, r = 13/(2*cos(PI/6)), $fn = 6);
  translate([0, 0, -30])
      cylinder(h = 30, r = 4, $fn = 64);
SCAD (3 lines) 
cylinder(h = 5.3, r = 13/(2*cos(PI/6)), $fn = 6);
translate([0, 0, -30])
    cylinder(h = 30, r = 4, $fn = 64);
i2 success →
iter 2
9.4s · 1176/1069t · $0.0060
diff vs i1: +0/-0 
  cylinder(h = 5.3, r = 13/(2*cos(PI/6)), $fn = 6);
  translate([0, 0, -30])
      cylinder(h = 30, r = 4, $fn = 64);
SCAD (3 lines) 
cylinder(h = 5.3, r = 13/(2*cos(PI/6)), $fn = 6);
translate([0, 0, -30])
    cylinder(h = 30, r = 4, $fn = 64);
i3 success →
iter 3
7.2s · 1176/804t · $0.0048
diff vs i2: +0/-0 
  cylinder(h = 5.3, r = 13/(2*cos(PI/6)), $fn = 6);
  translate([0, 0, -30])
      cylinder(h = 30, r = 4, $fn = 64);
SCAD (3 lines) 
cylinder(h = 5.3, r = 13/(2*cos(PI/6)), $fn = 6);
translate([0, 0, -30])
    cylinder(h = 30, r = 4, $fn = 64);