SCAD (9 lines)
// M8 六角ボルト(ねじ山省略)
union() {
// 頭部:対辺距離 13 mm、高さ 5.3 mm
cylinder(h = 5.3, d = 26 / sqrt(3), $fn = 6);
// シャンク:直径 8 mm、長さ 30 mm
translate([0, 0, -30])
cylinder(h = 30, d = 8, $fn = 64);
} gpt-6-sol 6 run / 累計 35.6s / 累計 $0.0221
// M8 hex bolt (thread omitted)
union() {
// Hex head: 13 mm across flats, 5.3 mm high
cylinder(h = 5.3, d = 13 / cos(30), $fn = 6);
// Shank: 8 mm diameter, extending 30 mm below the head
translate([0, 0, -30])
cylinder(h = 30, d = 8, $fn = 64);
} OpenSCAD で、規格に準じた M8 サイズの六角ボルトを作ってください。 ねじ山自体は省略してよく、円柱のシャンクで構いません。 寸法は以下に従ってください: - 頭部は六角柱で、対辺距離(across-flats)13mm、高さ 5.3mm - シャンク(軸部)は直径 8mm、長さ 30mm の円柱 - ボルト全体の中心軸は +Z 軸方向 - 頭部の底面が原点(z=0)に来るように配置し、シャンクは z<0 側へ伸ばす 完成したコード全体を ```openscad ... ``` のフェンスで囲んで出力してください。コードのみで、追加の説明は不要です。
effort
// M8 六角ボルト(ねじ山省略)
union() {
// 頭部:対辺距離 13 mm、高さ 5.3 mm
cylinder(h = 5.3, d = 26 / sqrt(3), $fn = 6);
// シャンク:直径 8 mm、長さ 30 mm
translate([0, 0, -30])
cylinder(h = 30, d = 8, $fn = 64);
}
// M8 hex bolt (thread omitted)
union() {
// Hex head: 13 mm across flats, 5.3 mm high
cylinder(h = 5.3, d = 13 / cos(30), $fn = 6);
// Shank: 8 mm diameter, extending 30 mm below the head
translate([0, 0, -30])
cylinder(h = 30, d = 8, $fn = 64);
}
head_across_flats = 13;
head_height = 5.3;
shank_diameter = 8;
shank_length = 30;
head_radius = head_across_flats / sqrt(3);
union() {
linear_extrude(height = head_height)
polygon([
for (i = [0:5])
[head_radius * cos(i * 60),
head_radius * sin(i * 60)]
]);
translate([0, 0, -shank_length])
cylinder(h = shank_length, d = shank_diameter, $fn = 64);
}
union() {
// 六角頭部:対辺距離 13 mm、高さ 5.3 mm
cylinder(h = 5.3, r = 13 / sqrt(3), $fn = 6);
// シャンク:直径 8 mm、長さ 30 mm
translate([0, 0, -30])
cylinder(h = 30, d = 8, $fn = 96);
}
head_across_flats = 13;
head_height = 5.3;
shank_diameter = 8;
shank_length = 30;
union() {
linear_extrude(height = head_height)
polygon([
for (i = [0:5])
[head_across_flats / sqrt(3) * cos(30 + i * 60),
head_across_flats / sqrt(3) * sin(30 + i * 60)]
]);
translate([0, 0, -shank_length])
cylinder(d = shank_diameter, h = shank_length, $fn = 64);
}