vibe-openscad

tier-1-cube-with-hole / gpt-5-mini-2025-08-07

7 run / 累計 57.3s / 累計 $0.0074

openai gpt 5 mini 2025-08-07 bare

bare (provider default effort)

run detail →
render
bare render of tier-1-cube-with-hole
loading STL…
success 6.1s · 82/363t · $0.0007
SCAD (6 lines) 
$fn = 100;

difference() {
    cube([50, 50, 50], center = true);
    cylinder(h = 100, r = 10, center = true);
}

prompt

OpenSCAD で、50mm 角の立方体の中央に、直径 20mm の貫通穴を z 軸方向に開けたモデルを作成してください。

完成したコード全体を ```openscad ... ``` のフェンスで囲んで出力してください。コードのみで、追加の説明は不要です。

variant: effort

low success →
low
4.6s · 82/226t · $0.0005
SCAD (7 lines) 
// 50mm 角の立方体の中央に直径20mmの貫通穴（z軸方向）を開ける

difference() {
    cube([50, 50, 50], center = true);
    // 十分な高さを持たせて貫通させる
    cylinder(h = 60, d = 20, center = true, $fn = 100);
}
medium (default) success →
medium
6.1s · 82/363t · $0.0007
SCAD (6 lines) 
$fn = 100;

difference() {
    cube([50, 50, 50], center = true);
    cylinder(h = 100, r = 10, center = true);
}
high success →
high
17.6s · 82/1145t · $0.0023
SCAD (5 lines) 
$fn = 64;
difference() {
    cube([50, 50, 50], center = true);
    cylinder(h = 60, r = 10, center = true);
}
maxnot run
—
xhighnot run
—

iteration: iter-png

i1 success →
iter 1
8.7s · 792/534t · $0.0013
diff vs bare: +0/-0 
  $fn = 100;
  
  difference() {
      cube([50, 50, 50], center = true);
      cylinder(h = 100, r = 10, center = true);
  }
SCAD (6 lines) 
$fn = 100;

difference() {
    cube([50, 50, 50], center = true);
    cylinder(h = 100, r = 10, center = true);
}
i2 success →
iter 2
7.6s · 792/346t · $0.0009
diff vs i1: +0/-0 
  $fn = 100;
  
  difference() {
      cube([50, 50, 50], center = true);
      cylinder(h = 100, r = 10, center = true);
  }
SCAD (6 lines) 
$fn = 100;

difference() {
    cube([50, 50, 50], center = true);
    cylinder(h = 100, r = 10, center = true);
}
i3 success →
iter 3
6.7s · 792/396t · $0.0010
diff vs i2: +0/-0 
  $fn = 100;
  
  difference() {
      cube([50, 50, 50], center = true);
      cylinder(h = 100, r = 10, center = true);
  }
SCAD (6 lines) 
$fn = 100;

difference() {
    cube([50, 50, 50], center = true);
    cylinder(h = 100, r = 10, center = true);
}