vibe-openscad

tier-1-cube-with-hole / gemini-2.5-flash-lite

6 run / 累計 17.2s / 累計 $0.0004

gemini flash-lite 2.5 bare

bare (provider default effort)

run detail →
render
bare render of tier-1-cube-with-hole
loading STL…
success 0.9s · 68/79t · <$0.0001
SCAD (8 lines) 
module hollow_cube(size, hole_diameter) {
    difference() {
        cube(size, center = true);
        cylinder(h = size * 2, d = hole_diameter, center = true);
    }
}

hollow_cube(size = 50, hole_diameter = 20);

prompt

OpenSCAD で、50mm 角の立方体の中央に、直径 20mm の貫通穴を z 軸方向に開けたモデルを作成してください。

完成したコード全体を ```openscad ... ``` のフェンスで囲んで出力してください。コードのみで、追加の説明は不要です。

variant: thinking

off success →
off
1.0s · 68/50t · <$0.0001
SCAD (4 lines) 
difference() {
    cube([50, 50, 50], center = true);
    cylinder(h = 50, d = 20, center = true);
}
adaptivenot run
—
dynamic (default) success →
dynamic
0.9s · 68/79t · <$0.0001
SCAD (8 lines) 
module hollow_cube(size, hole_diameter) {
    difference() {
        cube(size, center = true);
        cylinder(h = size * 2, d = hole_diameter, center = true);
    }
}

hollow_cube(size = 50, hole_diameter = 20);

iteration: iter-png

i1 success →
iter 1
6.5s · 467/145t · $0.0001
diff vs bare: +0/-0 
  module hollow_cube(size, hole_diameter) {
      difference() {
          cube(size, center = true);
          cylinder(h = size * 2, d = hole_diameter, center = true);
      }
  }
  
  hollow_cube(size = 50, hole_diameter = 20);
SCAD (8 lines) 
module hollow_cube(size, hole_diameter) {
    difference() {
        cube(size, center = true);
        cylinder(h = size * 2, d = hole_diameter, center = true);
    }
}

hollow_cube(size = 50, hole_diameter = 20);
i2 success →
iter 2
3.6s · 467/88t · <$0.0001
diff vs i1: +1/-1 
  module hollow_cube(size, hole_diameter) {
      difference() {
          cube(size, center = true);
-         cylinder(h = size * 2, d = hole_diameter, center = true);
+         translate([0, 0, -size/2]) cylinder(h = size, d = hole_diameter, center = true);
      }
  }
  
  hollow_cube(size = 50, hole_diameter = 20);
SCAD (8 lines) 
module hollow_cube(size, hole_diameter) {
    difference() {
        cube(size, center = true);
        translate([0, 0, -size/2]) cylinder(h = size, d = hole_diameter, center = true);
    }
}

hollow_cube(size = 50, hole_diameter = 20);
i3 success →
iter 3
4.1s · 476/201t · $0.0001
diff vs i2: +0/-0 
  module hollow_cube(size, hole_diameter) {
      difference() {
          cube(size, center = true);
          translate([0, 0, -size/2]) cylinder(h = size, d = hole_diameter, center = true);
      }
  }
  
  hollow_cube(size = 50, hole_diameter = 20);
SCAD (8 lines) 
module hollow_cube(size, hole_diameter) {
    difference() {
        cube(size, center = true);
        translate([0, 0, -size/2]) cylinder(h = size, d = hole_diameter, center = true);
    }
}

hollow_cube(size = 50, hole_diameter = 20);