vibe-openscad

tier-1-cube-with-hole / claude-sonnet-4-6

8 run / 累計 23.8s / 累計 $0.0208

claude sonnet 4.6 bare

bare (provider default effort)

run detail →
render
bare render of tier-1-cube-with-hole
loading STL…
success 3.4s · 104/55t · $0.0011
SCAD (4 lines) 
difference() {
    cube([50, 50, 50], center = true);
    cylinder(h = 60, r = 10, center = true, $fn = 64);
}

prompt

OpenSCAD で、50mm 角の立方体の中央に、直径 20mm の貫通穴を z 軸方向に開けたモデルを作成してください。

完成したコード全体を ```openscad ... ``` のフェンスで囲んで出力してください。コードのみで、追加の説明は不要です。

variant: effort

low success →
low
2.1s · 104/55t · $0.0011
SCAD (4 lines) 
difference() {
    cube([50, 50, 50], center = true);
    cylinder(h = 51, d = 20, center = true, $fn = 64);
}
mediumnot run
—
high (default) success →
high
2.4s · 104/55t · $0.0011
SCAD (4 lines) 
difference() {
    cube([50, 50, 50], center = true);
    cylinder(h = 60, r = 10, center = true, $fn = 64);
}
maxnot run
—
xhighnot run
—

variant: thinking

off success →
off
2.4s · 104/55t · $0.0011
SCAD (4 lines) 
difference() {
    cube([50, 50, 50], center = true);
    cylinder(h = 60, r = 10, center = true, $fn = 64);
}
adaptive (default) success →
adaptive
2.1s · 104/55t · $0.0011
SCAD (4 lines) 
difference() {
    cube([50, 50, 50], center = true);
    cylinder(h = 51, d = 20, center = true, $fn = 64);
}
dynamicnot run
—

iteration: iter-png

i1 success →
iter 1
4.8s · 908/237t · $0.0063
diff vs bare: +1/-1 
  difference() {
      cube([50, 50, 50], center = true);
-     cylinder(h = 60, r = 10, center = true, $fn = 64);
+     cylinder(h = 100, r = 10, center = true, $fn = 64);
  }
SCAD (4 lines) 
difference() {
    cube([50, 50, 50], center = true);
    cylinder(h = 100, r = 10, center = true, $fn = 64);
}
i2 success →
iter 2
1.8s · 908/55t · $0.0035
diff vs i1: +0/-0 
  difference() {
      cube([50, 50, 50], center = true);
      cylinder(h = 100, r = 10, center = true, $fn = 64);
  }
SCAD (4 lines) 
difference() {
    cube([50, 50, 50], center = true);
    cylinder(h = 100, r = 10, center = true, $fn = 64);
}
i3 success →
iter 3
4.8s · 908/172t · $0.0053
diff vs i2: +1/-1 
  difference() {
      cube([50, 50, 50], center = true);
-     cylinder(h = 100, r = 10, center = true, $fn = 64);
+     cylinder(h = 60, r = 10, center = true, $fn = 64);
  }
SCAD (4 lines) 
difference() {
    cube([50, 50, 50], center = true);
    cylinder(h = 60, r = 10, center = true, $fn = 64);
}