vibe-openscad

tier-1-cube-with-hole / claude-opus-4-8

10 run / 累計 34.3s / 累計 $0.0521

claude opus 4.8 bare

bare (provider default effort)

run detail →
render
bare render of tier-1-cube-with-hole
loading STL…
success 2.4s · 111/60t · $0.0021
SCAD (4 lines) 
difference() {
    cube([50, 50, 50], center = true);
    cylinder(h = 51, d = 20, center = true, $fn = 100);
}

prompt

OpenSCAD で、50mm 角の立方体の中央に、直径 20mm の貫通穴を z 軸方向に開けたモデルを作成してください。

完成したコード全体を ```openscad ... ``` のフェンスで囲んで出力してください。コードのみで、追加の説明は不要です。

variant: effort

low success →
low
2.0s · 111/60t · $0.0021
SCAD (4 lines) 
difference() {
    cube([50, 50, 50], center = true);
    cylinder(h = 51, d = 20, center = true, $fn = 100);
}
mediumnot run
—
high (default) success →
high
2.1s · 111/60t · $0.0021
SCAD (4 lines) 
difference() {
    cube([50, 50, 50], center = true);
    cylinder(h = 51, d = 20, center = true, $fn = 100);
}
max success →
max
2.6s · 109/60t · $0.0020
SCAD (4 lines) 
difference() {
    cube([50, 50, 50], center = true);
    cylinder(h = 51, d = 20, center = true, $fn = 64);
}
xhigh success →
xhigh
2.1s · 111/60t · $0.0021
SCAD (4 lines) 
difference() {
    cube([50, 50, 50], center = true);
    cylinder(h = 51, d = 20, center = true, $fn = 100);
}

variant: thinking

off success →
off
2.1s · 111/60t · $0.0021
SCAD (4 lines) 
difference() {
    cube([50, 50, 50], center = true);
    cylinder(h = 51, d = 20, center = true, $fn = 100);
}
adaptive (default) success →
adaptive
2.1s · 111/60t · $0.0021
SCAD (4 lines) 
difference() {
    cube([50, 50, 50], center = true);
    cylinder(h = 51, d = 20, center = true, $fn = 100);
}
dynamicnot run
—

iteration: iter-png

i1 success →
iter 1
5.7s · 932/273t · $0.0115
diff vs bare: +4/-1 
  difference() {
+     // 50mm角の立方体を原点中心に配置
      cube([50, 50, 50], center = true);
-     cylinder(h = 51, d = 20, center = true, $fn = 100);
+     // 直径20mmの穴をz軸方向に貫通（原点中心）
+     translate([0, 0, 0])
+         cylinder(h = 60, d = 20, center = true, $fn = 100);
  }
SCAD (7 lines) 
difference() {
    // 50mm角の立方体を原点中心に配置
    cube([50, 50, 50], center = true);
    // 直径20mmの穴をz軸方向に貫通（原点中心）
    translate([0, 0, 0])
        cylinder(h = 60, d = 20, center = true, $fn = 100);
}
i2 success →
iter 2
7.2s · 993/352t · $0.0138
diff vs i1: +5/-5 
  difference() {
-     // 50mm角の立方体を原点中心に配置
-     cube([50, 50, 50], center = true);
-     // 直径20mmの穴をz軸方向に貫通（原点中心）
-     translate([0, 0, 0])
-         cylinder(h = 60, d = 20, center = true, $fn = 100);
+     // 50mm角の立方体（原点に配置）
+     cube([50, 50, 50]);
+     // 直径20mmの穴をz軸方向に貫通（立方体の中心に配置）
+     translate([25, 25, -5])
+         cylinder(h = 60, d = 20, $fn = 100);
  }
SCAD (7 lines) 
difference() {
    // 50mm角の立方体（原点に配置）
    cube([50, 50, 50]);
    // 直径20mmの穴をz軸方向に貫通（立方体の中心に配置）
    translate([25, 25, -5])
        cylinder(h = 60, d = 20, $fn = 100);
}
i3 success →
iter 3
6.0s · 990/302t · $0.0125
diff vs i2: +3/-4 
  difference() {
-     // 50mm角の立方体（原点に配置）
-     cube([50, 50, 50]);
+     // 50mm角の立方体（原点を中心に配置）
+     cube([50, 50, 50], center = true);
      // 直径20mmの穴をz軸方向に貫通（立方体の中心に配置）
-     translate([25, 25, -5])
-         cylinder(h = 60, d = 20, $fn = 100);
+     cylinder(h = 60, d = 20, center = true, $fn = 100);
  }
SCAD (6 lines) 
difference() {
    // 50mm角の立方体（原点を中心に配置）
    cube([50, 50, 50], center = true);
    // 直径20mmの穴をz軸方向に貫通（立方体の中心に配置）
    cylinder(h = 60, d = 20, center = true, $fn = 100);
}