bare/claude-opus-4-0 / tier-3-butt-hinge

success tier 3

bare (claude opus 4)

render

loading STL…

success 30.3s · 707/1933t · $0.1556

SCAD (151 lines)

// Butt hinge parameters
leaf_width = 25;
leaf_height = 30;
leaf_thickness = 2;
pin_diameter = 4;
pin_length = 32;
knuckle_outer_diameter = 8;
knuckle_inner_diameter = 4.6;
knuckle_height = 6;
num_knuckles = 5;

// Screw hole parameters
screw_hole_diameter = 3.2;
countersink_diameter = 6;
countersink_depth = 1;
screw_spacing = 8;

// Pin (centered on Y-axis)
color("Silver")
translate([0, -1, 0])
cylinder(h = pin_length, d = pin_diameter, $fn = 32);

// Left leaf (x < 0)
color("DarkGray")
translate([0, 0, 0])
union() {
    // Flat plate
    translate([-leaf_width, 0, -leaf_thickness/2])
    cube([leaf_width - knuckle_outer_diameter/2, leaf_height, leaf_thickness]);
    
    // Knuckles (positions 0, 2, 4)
    for (i = [0, 2, 4]) {
        translate([0, i * knuckle_height, 0])
        difference() {
            cylinder(h = knuckle_height, d = knuckle_outer_diameter, $fn = 32);
            cylinder(h = knuckle_height, d = knuckle_inner_diameter, $fn = 32);
            // Cut half cylinder
            translate([knuckle_outer_diameter/2, 0, 0])
            cube([knuckle_outer_diameter, knuckle_height, knuckle_height], center = true);
        }
    }
    
    // Screw holes
    for (i = [0, 1, 2]) {
        translate([-leaf_width * 0.6, leaf_height/2 + (i - 1) * screw_spacing, 0])
        difference() {
            cylinder(h = 0.01, d = 0.01); // Dummy for union
            // Countersink
            translate([0, 0, leaf_thickness/2 - countersink_depth])
            cylinder(h = countersink_depth, d1 = screw_hole_diameter, d2 = countersink_diameter, $fn = 32);
            // Through hole
            translate([0, 0, -leaf_thickness/2 - 0.1])
            cylinder(h = leaf_thickness + 0.2, d = screw_hole_diameter, $fn = 32);
        }
    }
}

// Right leaf (x > 0)
color("DarkGray")
translate([0, 0, 0])
union() {
    // Flat plate
    translate([knuckle_outer_diameter/2, 0, -leaf_thickness/2])
    cube([leaf_width - knuckle_outer_diameter/2, leaf_height, leaf_thickness]);
    
    // Knuckles (positions 1, 3)
    for (i = [1, 3]) {
        translate([0, i * knuckle_height, 0])
        difference() {
            cylinder(h = knuckle_height, d = knuckle_outer_diameter, $fn = 32);
            cylinder(h = knuckle_height, d = knuckle_inner_diameter, $fn = 32);
            // Cut half cylinder
            translate([-knuckle_outer_diameter/2, 0, 0])
            cube([knuckle_outer_diameter, knuckle_height, knuckle_height], center = true);
        }
    }
    
    // Screw holes
    for (i = [0, 1, 2]) {
        translate([leaf_width * 0.6, leaf_height/2 + (i - 1) * screw_spacing, 0])
        difference() {
            cylinder(h = 0.01, d = 0.01); // Dummy for union
            // Countersink
            translate([0, 0, leaf_thickness/2 - countersink_depth])
            cylinder(h = countersink_depth, d1 = screw_hole_diameter, d2 = countersink_diameter, $fn = 32);
            // Through hole
            translate([0, 0, -leaf_thickness/2 - 0.1])
            cylinder(h = leaf_thickness + 0.2, d = screw_hole_diameter, $fn = 32);
        }
    }
}

// Apply screw holes to leaves
difference() {
    union() {
        // Left leaf base
        color("DarkGray")
        translate([-leaf_width, 0, -leaf_thickness/2])
        cube([leaf_width - knuckle_outer_diameter/2, leaf_height, leaf_thickness]);
        
        // Right leaf base
        color("DarkGray")
        translate([knuckle_outer_diameter/2, 0, -leaf_thickness/2])
        cube([leaf_width - knuckle_outer_diameter/2, leaf_height, leaf_thickness]);
    }
    
    // Left leaf screw holes
    for (i = [0, 1, 2]) {
        translate([-leaf_width * 0.6, leaf_height/2 + (i - 1) * screw_spacing, 0]) {
            // Countersink
            translate([0, 0, leaf_thickness/2 - countersink_depth])
            cylinder(h = countersink_depth + 0.1, d1 = screw_hole_diameter, d2 = countersink_diameter, $fn = 32);
            // Through hole
            cylinder(h = leaf_thickness + 1, d = screw_hole_diameter, center = true, $fn = 32);
        }
    }
    
    // Right leaf screw holes
    for (i = [0, 1, 2]) {
        translate([leaf_width * 0.6, leaf_height/2 + (i - 1) * screw_spacing, 0]) {
            // Countersink
            translate([0, 0, leaf_thickness/2 - countersink_depth])
            cylinder(h = countersink_depth + 0.1, d1 = screw_hole_diameter, d2 = countersink_diameter, $fn = 32);
            // Through hole
            cylinder(h = leaf_thickness + 1, d = screw_hole_diameter, center = true, $fn = 32);
        }
    }
}

// Knuckles
color("DarkGray") {
    // Left leaf knuckles
    for (i = [0, 2, 4]) {
        translate([0, i * knuckle_height, 0])
        difference() {
            translate([-knuckle_outer_diameter/2, 0, 0])
            cube([knuckle_outer_diameter/2, knuckle_height, knuckle_outer_diameter/2]);
            cylinder(h = knuckle_height, d = knuckle_inner_diameter, $fn = 32);
        }
    }
    
    // Right leaf knuckles
    for (i = [1, 3]) {
        translate([0, i * knuckle_height, 0])
        difference() {
            translate([0, 0, 0])
            cube([knuckle_outer_diameter/2, knuckle_height, knuckle_outer_diameter/2]);
            cylinder(h = knuckle_height, d = knuckle_inner_diameter, $fn = 32);
        }
    }
}

```openscad
// Butt hinge parameters
leaf_width = 25;
leaf_height = 30;
leaf_thickness = 2;
pin_diameter = 4;
pin_length = 32;
knuckle_outer_diameter = 8;
knuckle_inner_diameter = 4.6;
knuckle_height = 6;
num_knuckles = 5;

// Screw hole parameters
screw_hole_diameter = 3.2;
countersink_diameter = 6;
countersink_depth = 1;
screw_spacing = 8;

// Pin (centered on Y-axis)
color("Silver")
translate([0, -1, 0])
cylinder(h = pin_length, d = pin_diameter, $fn = 32);

// Left leaf (x < 0)
color("DarkGray")
translate([0, 0, 0])
union() {
    // Flat plate
    translate([-leaf_width, 0, -leaf_thickness/2])
    cube([leaf_width - knuckle_outer_diameter/2, leaf_height, leaf_thickness]);
    
    // Knuckles (positions 0, 2, 4)
    for (i = [0, 2, 4]) {
        translate([0, i * knuckle_height, 0])
        difference() {
            cylinder(h = knuckle_height, d = knuckle_outer_diameter, $fn = 32);
            cylinder(h = knuckle_height, d = knuckle_inner_diameter, $fn = 32);
            // Cut half cylinder
            translate([knuckle_outer_diameter/2, 0, 0])
            cube([knuckle_outer_diameter, knuckle_height, knuckle_height], center = true);
        }
    }
    
    // Screw holes
    for (i = [0, 1, 2]) {
        translate([-leaf_width * 0.6, leaf_height/2 + (i - 1) * screw_spacing, 0])
        difference() {
            cylinder(h = 0.01, d = 0.01); // Dummy for union
            // Countersink
            translate([0, 0, leaf_thickness/2 - countersink_depth])
            cylinder(h = countersink_depth, d1 = screw_hole_diameter, d2 = countersink_diameter, $fn = 32);
            // Through hole
            translate([0, 0, -leaf_thickness/2 - 0.1])
            cylinder(h = leaf_thickness + 0.2, d = screw_hole_diameter, $fn = 32);
        }
    }
}

// Right leaf (x > 0)
color("DarkGray")
translate([0, 0, 0])
union() {
    // Flat plate
    translate([knuckle_outer_diameter/2, 0, -leaf_thickness/2])
    cube([leaf_width - knuckle_outer_diameter/2, leaf_height, leaf_thickness]);
    
    // Knuckles (positions 1, 3)
    for (i = [1, 3]) {
        translate([0, i * knuckle_height, 0])
        difference() {
            cylinder(h = knuckle_height, d = knuckle_outer_diameter, $fn = 32);
            cylinder(h = knuckle_height, d = knuckle_inner_diameter, $fn = 32);
            // Cut half cylinder
            translate([-knuckle_outer_diameter/2, 0, 0])
            cube([knuckle_outer_diameter, knuckle_height, knuckle_height], center = true);
        }
    }
    
    // Screw holes
    for (i = [0, 1, 2]) {
        translate([leaf_width * 0.6, leaf_height/2 + (i - 1) * screw_spacing, 0])
        difference() {
            cylinder(h = 0.01, d = 0.01); // Dummy for union
            // Countersink
            translate([0, 0, leaf_thickness/2 - countersink_depth])
            cylinder(h = countersink_depth, d1 = screw_hole_diameter, d2 = countersink_diameter, $fn = 32);
            // Through hole
            translate([0, 0, -leaf_thickness/2 - 0.1])
            cylinder(h = leaf_thickness + 0.2, d = screw_hole_diameter, $fn = 32);
        }
    }
}

// Apply screw holes to leaves
difference() {
    union() {
        // Left leaf base
        color("DarkGray")
        translate([-leaf_width, 0, -leaf_thickness/2])
        cube([leaf_width - knuckle_outer_diameter/2, leaf_height, leaf_thickness]);
        
        // Right leaf base
        color("DarkGray")
        translate([knuckle_outer_diameter/2, 0, -leaf_thickness/2])
        cube([leaf_width - knuckle_outer_diameter/2, leaf_height, leaf_thickness]);
    }
    
    // Left leaf screw holes
    for (i = [0, 1, 2]) {
        translate([-leaf_width * 0.6, leaf_height/2 + (i - 1) * screw_spacing, 0]) {
            // Countersink
            translate([0, 0, leaf_thickness/2 - countersink_depth])
            cylinder(h = countersink_depth + 0.1, d1 = screw_hole_diameter, d2 = countersink_diameter, $fn = 32);
            // Through hole
            cylinder(h = leaf_thickness + 1, d = screw_hole_diameter, center = true, $fn = 32);
        }
    }
    
    // Right leaf screw holes
    for (i = [0, 1, 2]) {
        translate([leaf_width * 0.6, leaf_height/2 + (i - 1) * screw_spacing, 0]) {
            // Countersink
            translate([0, 0, leaf_thickness/2 - countersink_depth])
            cylinder(h = countersink_depth + 0.1, d1 = screw_hole_diameter, d2 = countersink_diameter, $fn = 32);
            // Through hole
            cylinder(h = leaf_thickness + 1, d = screw_hole_diameter, center = true, $fn = 32);
        }
    }
}

// Knuckles
color("DarkGray") {
    // Left leaf knuckles
    for (i = [0, 2, 4]) {
        translate([0, i * knuckle_height, 0])
        difference() {
            translate([-knuckle_outer_diameter/2, 0, 0])
            cube([knuckle_outer_diameter/2, knuckle_height, knuckle_outer_diameter/2]);
            cylinder(h = knuckle_height, d = knuckle_inner_diameter, $fn = 32);
        }
    }
    
    // Right leaf knuckles
    for (i = [1, 3]) {
        translate([0, i * knuckle_height, 0])
        difference() {
            translate([0, 0, 0])
            cube([knuckle_outer_diameter/2, knuckle_height, knuckle_outer_diameter/2]);
            cylinder(h = knuckle_height, d = knuckle_inner_diameter, $fn = 32);
        }
    }
}
```

パラメータ (13) —

leaf_width leaf_height leaf_thickness pin_diameter pin_length knuckle_outer_diameter knuckle_inner_diameter knuckle_height num_knuckles screw_hole_diameter countersink_diameter countersink_depth screw_spacing

スライダを動かすと openscad-wasm で再レンダリング

runId	`bare_claude-opus-4-0-7fd386abeb62-2026-04-28T17-23-24-578Z`
matrixId	`bare/claude-opus-4-0`
signature	`7fd386abeb6298de…`
provider	anthropic
model	claude-opus-4-20250514
harness	bare
status	success
duration	30.29s (wallclock: load + prompt eval + generation + network)
tokens	707 in / 1933 out
wallclock tok/s	63.8 tok/s (end-to-end)
cost	$0.1556
createdAt	2026-04-28T17:23:24.578Z
gitCommit	`be87c9f2adaf`
openscad	OpenSCAD version 2026.04.27

iteration chain

各 iteration step は独立した benchmark run です。parentRunId で前段にリンクします。

→ children (1)

child iter-png-1_claude-opus-4-0-5c4085873bc1-2026-04-28T17-31-42-653Z

iter-png-1/claude-opus-4-0 success

prompt

OpenSCAD で、家具用の小型バット蝶番(butt hinge)を作ってください。
3 つのパーツ(左板、右板、ピン軸)が組み合わさって動作する完成品を、
「開いた状態(180°)」で 1 つの SCAD ファイルに配置して出力します。

寸法と配置:
- 板(leaf)2 枚: 30mm × 25mm × 厚さ 2mm の鉄板形状
  - 縦 30mm の辺がピン軸に沿う(ヒンジ軸方向)
  - 横 25mm の辺が回転で開く方向に伸びる
- ピン軸: 直径 4mm の円柱、長さ 32mm(両端 1mm ずつ knuckle から飛び出す)
- knuckle(筒部): 縦 30mm を 5 等分(各 6mm)に区切り、左板に 3 個・右板に 2 個を
  互い違いに配置(左板は外側 2 個 + 中央 1 個、右板は中間 2 個)
- knuckle 外径 8mm、内径はピン軸 + 0.3mm クリアランス(= 4.6mm 穴)
- 左板と右板はピン軸を共有して回転可能。180° 開いた状態で、両板の
  平らな面が同一平面に来るように配置する
- 各板の knuckle から離れた側に、M3 用の皿穴を 3 個ずつ
  (穴ピッチは板の縦方向に 8mm 間隔、皿穴は表面から見て直径 6mm × 深さ 1mm
  のテーパ + 直径 3.2mm の貫通穴)

座標系:
- ピン軸の中心線を Y 軸に重ねる(ピン軸は +Y 方向)
- 板の平らな面は Z 軸に直交し、左板が x<0 側、右板が x>0 側に伸びる(180° 開)
- knuckle は X=0 を中心とし、Y 方向に 6mm ずつ並ぶ

完成したコード全体を ```openscad ... ``` のフェンスで囲んで出力してください。
コードのみで、追加の説明は不要です。

bare/claude-opus-4-0 / tier-3-butt-hinge

meta

iteration chain

prompt