bare-xhigh/gpt-6.1-sol / tier-3-butt-hinge
success tier 3
bare (gpt 6.1 sol)
render
// 単位: mm
// ヒンジ軸: X=0, Z=0 の Y 軸。
// 板の表面: Z=0、裏面: Z=-2。
// 開き角: 180°=全開、0°=閉じた状態。
$fn = 96;
opening_angle = 180;
leaf_length = 30;
leaf_width = 25;
leaf_thickness = 2;
pin_diameter = 4;
pin_length = 32;
knuckle_diameter = 8;
knuckle_count = 5;
knuckle_length = leaf_length / knuckle_count;
// ピンに対して片側 0.3 mm、穴径は 4.6 mm。
pin_radial_clearance = 0.3;
bore_diameter = pin_diameter + 2 * pin_radial_clearance;
screw_hole_diameter = 3.2;
screw_pitch = 8;
countersink_diameter = 6;
countersink_depth = 1;
screw_outer_margin = 5;
eps = 0.01;
// 相手側の筒に板が干渉しないよう、矩形板を外径の外側に配置。
// 自分側の筒だけを短い接続部で板につなぐ。
barrel_leaf_clearance = 0.2;
leaf_inner_x = knuckle_diameter / 2 + barrel_leaf_clearance;
leaf_outer_x = leaf_inner_x + leaf_width;
neck_inner_x = bore_diameter / 2 + 0.3;
neck_overlap = 0.5;
neck_width = leaf_inner_x + neck_overlap - neck_inner_x;
screw_x = leaf_outer_x - screw_outer_margin;
screw_y_positions = [
leaf_length / 2 - screw_pitch,
leaf_length / 2,
leaf_length / 2 + screw_pitch
];
// ローカル Z 方向の円柱を +Y 方向へ向ける。
module cylinder_y(diameter, length) {
rotate([-90, 0, 0])
cylinder(d = diameter, h = length);
}
// Z=0 の表面から、深さ 1 mm の皿穴。
module countersunk_hole(x, y) {
translate([x, y, -leaf_thickness - eps])
cylinder(
d = screw_hole_diameter,
h = leaf_thickness + 2 * eps
);
// Z=0 で正確に直径 6 mm となるよう、テーパを上方へ延長。
translate([x, y, -countersink_depth])
cylinder(
h = countersink_depth + eps,
d1 = screw_hole_diameter,
d2 = countersink_diameter
+ (countersink_diameter - screw_hole_diameter)
* eps / countersink_depth
);
}
// side=-1: 左板、side=+1: 右板。
// 各筒は正確に 6 mm。隣接端面は接触するが体積は重ならない。
module leaf_part(side) {
indices = side < 0 ? [0, 2, 4] : [1, 3];
difference() {
union() {
// 30 × 25 × 2 mm の矩形板。
translate([
side < 0 ? -leaf_outer_x : leaf_inner_x,
0,
-leaf_thickness
])
cube([leaf_width, leaf_length, leaf_thickness]);
for (i = indices) {
// 筒部。
translate([0, i * knuckle_length, 0])
cylinder_y(
knuckle_diameter,
knuckle_length
);
// 板と自分側の筒を一体化する接続部。
translate([
side < 0
? -leaf_inner_x - neck_overlap
: neck_inner_x,
i * knuckle_length,
-leaf_thickness
])
cube([
neck_width,
knuckle_length,
leaf_thickness
]);
}
}
// すべての自分側の筒を同軸でくり抜く。
translate([0, -eps, 0])
cylinder_y(
bore_diameter,
leaf_length + 2 * eps
);
for (y = screw_y_positions)
countersunk_hole(side * screw_x, y);
}
}
module left_leaf() {
leaf_part(-1);
}
module right_leaf() {
leaf_part(1);
}
module hinge_pin() {
// 筒全体は Y=0~30、ピンは Y=-1~31。
translate([0, (leaf_length - pin_length) / 2, 0])
cylinder_y(pin_diameter, pin_length);
}
module butt_hinge(angle = 180) {
color([0.58, 0.60, 0.62])
left_leaf();
// Y 軸まわりに回転。180°では左右の表面がともに Z=0。
color([0.64, 0.66, 0.68])
rotate([0, angle - 180, 0])
right_leaf();
color([0.76, 0.78, 0.80])
hinge_pin();
}
butt_hinge(opening_angle); パラメータ (17) —
スライダを動かすと openscad-wasm で再レンダリング
prompt
OpenSCAD で、家具用の小型バット蝶番(butt hinge)を作ってください。 3 つのパーツ(左板、右板、ピン軸)が組み合わさって動作する完成品を、 「開いた状態(180°)」で 1 つの SCAD ファイルに配置して出力します。 寸法と配置: - 板(leaf)2 枚: 30mm × 25mm × 厚さ 2mm の鉄板形状 - 縦 30mm の辺がピン軸に沿う(ヒンジ軸方向) - 横 25mm の辺が回転で開く方向に伸びる - ピン軸: 直径 4mm の円柱、長さ 32mm(両端 1mm ずつ knuckle から飛び出す) - knuckle(筒部): 縦 30mm を 5 等分(各 6mm)に区切り、左板に 3 個・右板に 2 個を 互い違いに配置(左板は外側 2 個 + 中央 1 個、右板は中間 2 個) - knuckle 外径 8mm、内径はピン軸 + 0.3mm クリアランス(= 4.6mm 穴) - 左板と右板はピン軸を共有して回転可能。180° 開いた状態で、両板の 平らな面が同一平面に来るように配置する - 各板の knuckle から離れた側に、M3 用の皿穴を 3 個ずつ (穴ピッチは板の縦方向に 8mm 間隔、皿穴は表面から見て直径 6mm × 深さ 1mm のテーパ + 直径 3.2mm の貫通穴) 座標系: - ピン軸の中心線を Y 軸に重ねる(ピン軸は +Y 方向) - 板の平らな面は Z 軸に直交し、左板が x<0 側、右板が x>0 側に伸びる(180° 開) - knuckle は X=0 を中心とし、Y 方向に 6mm ずつ並ぶ 完成したコード全体を ```openscad ... ``` のフェンスで囲んで出力してください。 コードのみで、追加の説明は不要です。